Welcome to Bafinasa official website!

Emerald Green Velvet Cocktail Midi Dress for Women

Source:News / Time:2026-11-19

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is velvet in green, the inside is structure, and the two have to agree on the same sample. A Emerald Green Velvet Cocktail Midi Dress for Women reads as a short brief until the pattern is cut, and the shape only holds when the bodice seam, the waist seam and the hem allowance are settled together.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Structure and seams

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth.

Check the bodice seam after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the bodice seam. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

Spec sheet, line by line

Shellvelvet, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ150 pcs per style

What to check before bulk

  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Topstitch showing through a satin shell after pressing.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Options on the table

  • Back: centre zip, lace-up, or a covered button placket.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top