Welcome to Bafinasa official website!

Hot Summer Ditsy Floral Chiffon Off Shoulder Top

Source:News / Time:2026-11-19

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the collar. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample.

We start with chiffon on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Set the placket before the collar. Two millimetres of shift at the button stand is visible. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees. Shell buttons change the perceived price more than they change the cost. Decide early, because button size changes the placket width.

When the brief names the off shoulder, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The off shoulder reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Chiffon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Spec sheet, line by line

Shellchiffon, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

What to check before bulk

  • Sleeve gathered rather than eased, producing puckers that show on a plain cloth.
  • Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
  • Collar fused too hard, giving a plastic edge that cannot be pressed into shape.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the collar, shading between panels, and hems that go wavy after pressing.

Changes we can make at sample stage

  • Placket: full, half, hidden, or none with a keyhole opening.
  • Collar: classic point, camp, band, or removable.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top