Welcome to Bafinasa official website!

Burgundy Mesh Cutout Bodycon Dress

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. For mesh, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel.

Specification, item by item

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Liningunlined with faced seams
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

What to check before bulk

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Panel count from four to eight, with a small cost difference per unit.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Private label: woven label, care label and hangtag to your artwork.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top