Welcome to Bafinasa official website!

Hot Pink Mesh High Slit Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is hot pink mesh high slit bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Most of the money in a Hot Pink Mesh High Slit Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. A Hot Pink Mesh High Slit Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. For mesh, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with mesh on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

The sheet we need before costing

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaypink
Liningunlined with faced seams
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Customisation that does not break the price

  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top