Wholesale Burgundy Business Blazer Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Wholesale Burgundy Business Blazer Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in burgundy, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
Structure and seams
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
Changes we can make at sample stage
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.