Welcome to Bafinasa official website!

Wholesale White Office Blazer Dress for Office

Source:News / Time:2026-11-14

A Wholesale White Office Blazer Dress for Office reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Wholesale White Office Blazer Dress for Office can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

What to check before bulk

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

What we can change for you

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top