Wholesale Navy Blue Notch Lapel Blazer Office Dress for Office
Most of the money in a Wholesale Navy Blue Notch Lapel Blazer Office Dress for Office sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Wholesale Navy Blue Notch Lapel Blazer Office Dress for Office can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | navy |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
What we can change for you
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.