Wholesale Burgundy A-line Blazer Office Dress for Office
Written down, the request is wholesale burgundy a-line blazer office dress for office: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Most of the money in a Wholesale Burgundy A-line Blazer Office Dress for Office sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 100 pcs per colour |
Failure points worth designing out
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.
What we can change for you
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Private label: woven label, care label and hangtag to your artwork.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.