Camel Tailored Blazer Office Dress for Office Work
A Camel Tailored Blazer Office Dress for Office Work can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
When the brief names the tailored, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The tailored reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | camel |
| Lining | half lined to the hip |
| Closure | concealed side zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
What to check before bulk
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Options on the table
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Private label: woven label, care label and hangtag to your artwork.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.