Welcome to Bafinasa official website!

Charcoal Grey Tailored Blazer Office Dress for Office Work

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

We keep the tailored as its own pattern piece so it can be changed without re-cutting the body. The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningunlined with faced seams
Closureinvisible centre-back zip
Size run34-44 with a regional grade
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

What we can change for you

  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top