Women Over 50 Collarless Blazer Slit Back
When a request arrives with “women over 50 collarless blazer slit back” in it, the useful first question is not the price. It is which of these attributes the buyer actually intends to sell on.
In production this is a high slit blazer. A sheath blazer is straight and close, with a walking vent at the back and a lining that has to be cut a few millimetres shorter than the shell so it does not hang below the hem.
A high slit needs a faced placket and a bar-tack at the stop point. Without the tack, the slit splits past the stop within a season.
What Has To Be Specified
- Block: Sheath bodice, fitted on a real model at the middle size before grading.
- Detail: High Slit. A high slit needs a faced placket and a bar-tack at the stop point. Without the tack, the slit splits past the stop within a season.
- Colour: name the exact tone and send a swatch. In this category a photo is not a colour reference.
- Bodice structure: say whether the bodice is boned, fused, or soft. This single line decides the fit, the price and the packing.
- Lining: state bodice lining, skirt lining and whether the skirt is bagged out at the hem.
- Closure: name the type and position - invisible zip, lace-up back, or covered button placket.
- Sizing: give the size run, the grade rule and the fit model. A Gulf 2XL is not a European 2XL.
- Care: dry-clean-only is normal here; if the trim cannot survive solvent, say so before the label is printed.
Suggested Starting Specification
| Shell fabric | crepe - swatch-approved, one dye lot for bulk |
| Length | as per your spec sheet |
| Silhouette | Sheath |
| Bodice | High Slit |
| Colourway | buyer's colourway, lab-dipped |
| Lining | fully lined, bagged hem |
| Closure | corset lace-up back |
| Size run | 34-48 with a Gulf grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style for custom beading |
Where This Style Goes Wrong In Production
A sheath blazer is straight and close, with a walking vent at the back and a lining that has to be cut a few millimetres shorter than the shell so it does not hang below the hem.
A high slit needs a faced placket and a bar-tack at the stop point. Without the tack, the slit splits past the stop within a season.
Pressing decides the finish. Satin and taffeta take a needle mark in a second, and no amount of QC takes it out afterwards.
Two rolls of the same colour name will not match. Buy one lot, keep a roll reference with the order, and cut the whole run from it.
The hem is where a cheap build shows. A 3 cm hem with a clean catch-stitch reads expensive; a 1 cm overlocked hem reads fast fashion.
Options We Can Build To
- Packing: flat-fold with tissue, hanger-ready, or individual sealed bag for glitter and bead styles.
- Detail alternatives on the High Slit: scaled up, reduced to a plain panel, or moved to the back for a cleaner front.
- Closure: invisible zip, exposed zip, corset lace-up or button placket, each with its own sample requirement.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own spec sheet.
- Lining: unlined bodice with a lined skirt, half-lined, or fully lined - the last one changes the hand and the cost together.
Pre-production sample approval, in-line inspection during cutting, beading and sewing, and a final AQL inspection before packing, with measurement reports and photos shared before shipment.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
