Women's Petite Women Metallic Bronze African Dashiki Shirt with Headwrap

The phrase “women's petite women metallic bronze african dashiki shirt with headwrap” reads like a styling note and behaves like a spec sheet. Once you unpack it, it names a cloth, a cut and a wearer - and those three decisions fix roughly eighty per cent of the cost before a single sample is cut.

In practical terms this is a shirt in metallic wax built for women. Metallic wax carries a foil-like surface on a wax-print base. The metallic layer is the fragile part: it creases white at a hard fold and it cannot be pressed directly with a hot iron. A shirt lives or dies on the collar and the placket. Both have to be cut with the print in mind, and the yoke is the panel that decides whether the motif lands on the shoulder.

The size run is the first commercial decision: a four-size run sells a test order, a ten-size run sells a container.

What Has To Be Specified

• Shell: metallic wax, weight and hand approved on a physical swatch, not on a screen.
• Block: shirt, fitted on a real model at the middle size before grading.
• Detail: a matching headwrap. The headwrap is cut from the same lot as the garment and finished on all four edges; if it is a separate SKU it still has to be photographed with the dress.
• Colour: bronze, with a lab dip approved against your own colour card and a light-box check (D65 and TL84).
• Lining: state unlined, half-lined or fully lined. This single line changes the hand, the packing and the cost.
• Closure: name the type and the position. “Back zip” is not a specification; “invisible zip, CB, 55 cm, self-fabric guard” is.
• Sizing: give the size run, the grade rule and the target fit model. A four-size test and a ten-size container run are two different projects.
• Trim and hardware: bead, cord, eyelet or feather, with a colour reference and a pull-strength requirement for anything on a children's style.

Suggested Starting Specification

Where This Style Goes Wrong In Production

Metallic wax carries a foil-like surface on a wax-print base. The metallic layer is the fragile part: it creases white at a hard fold and it cannot be pressed directly with a hot iron.

The headwrap is cut from the same lot as the garment and finished on all four edges; if it is a separate SKU it still has to be photographed with the dress.

A shirt lives or dies on the collar and the placket. Both have to be cut with the print in mind, and the yoke is the panel that decides whether the motif lands on the shoulder.

Trims are quoted per piece and bought per roll. A 15% trim allowance sounds generous until the third size run lands.

The first sample usually passes on the mannequin and fails on a body: the waist sits high, the armhole cuts, or the sweep is 4 cm short. Fit on a real model before you approve anything.

Grading is where the money disappears. Every detail that is placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Options We Can Build To

• Packing: flat-fold with tissue, hanger-ready, or individual polybag with a branded insert.
• Detail variations on the a matching headwrap: scaled up, scaled down, or replaced with a plain panel at a lower price point.
• Sizing: a four-size test run, a standard eight-size run, or a graded run to your own spec sheet.
• Sizing: a four-size test run, a standard eight-size run, or a graded run to your own spec sheet.
• Packing: flat-fold with tissue, hanger-ready, or individual polybag with a branded insert.

Pre-production sample approval, in-line inspection during cutting and sewing, and a final AQL inspection before packing, with measurement reports and photos shared before shipment.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.