Welcome to Bafinasa official website!
Your Location: Home - News - Printed Chiffon Sundress

Printed Chiffon Sundress

Source:News / Time:2026-11-19

Most of the money in a Printed Chiffon Sundress sits in three places: the cloth, the shoulder seam, and the labour that keeps the side seam flat after pressing. Written down, the request is printed chiffon sundress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the shoulder seam. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with chiffon on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is cut shorter and attached at the waist, so the shell floats over it. Needle and thread matter here. A 70/10 needle and fine polyester thread keep the seam from puckering. Hem with a narrow rolled edge. A wide hem pulls light cloth out of shape.

The hem reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the hem after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

Specification, item by item

Shellchiffon, swatch-approved, one dye lot for bulk
Bodychiffon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

What to check before bulk

  • Lining sewn to the same length as the shell, so the two drag each other.
  • Over-pressed seams that kill the drape and make the dress look flat.
  • Cutting before the cloth relaxes, so the finished hem is uneven.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Lining: full, to the knee, or a separate slip.
  • Layer count at the skirt: one, two, or three tiers.
  • Sleeve: flutter, cap, or long with a cuff.
  • Print or solid, with placement controlled at the front panel.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top