Welcome to Bafinasa official website!

Casual Spring Summer Sheer Chiffon Tunic Top

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the collar. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the collar. Without it, the seam ridge shows through at the first press.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. Shell buttons change the perceived price more than they change the cost. Decide early, because button size changes the placket width. Set the placket before the collar. Two millimetres of shift at the button stand is visible. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees.

When the brief names the collar, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the collar after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the collar to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the collar.

What goes on the spec sheet

Shellchiffon, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

What to check before bulk

  • Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
  • Sleeve gathered rather than eased, producing puckers that show on a plain cloth.
  • Placket cut on the bias by accident, so it twists after washing.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Options on the table

  • Collar: classic point, camp, band, or removable.
  • Back: plain, box pleat, or yoke with a loop.
  • Placket: full, half, hidden, or none with a keyhole opening.
  • Cuff: buttoned, elasticated, or turned back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top