Welcome to Bafinasa official website!

Summer 2026 Silk Chiffon Tunic Top

Source:News / Time:2026-11-19

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the collar. A Summer 2026 Silk Chiffon Tunic Top reads as a short brief until the pattern is cut, and the shape only holds when the collar, the placket and the hem allowance are settled together. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the collar. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with silk on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. On light cloth, ease the sleeve head rather than gathering it. The sleeve should hold shape without puckers. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees.

We keep the collar as its own pattern piece so it can be changed without re-cutting the body. The collar is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the collar. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the collar to move at different rates.

Specification, item by item

Shellsilk, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

The places this usually goes wrong

  • Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
  • Sleeve gathered rather than eased, producing puckers that show on a plain cloth.
  • Placket cut on the bias by accident, so it twists after washing.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the collar, shading between panels, and hems that go wavy after pressing. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Changes we can make at sample stage

  • Back: plain, box pleat, or yoke with a loop.
  • Collar: classic point, camp, band, or removable.
  • Cuff: buttoned, elasticated, or turned back.
  • Placket: full, half, hidden, or none with a keyhole opening.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top