Welcome to Bafinasa official website!

Women's Georgette Chiffon Tunic Top

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. A Women's Georgette Chiffon Tunic Top reads as a short brief until the pattern is cut, and the shape only holds when the collar, the placket and the hem allowance are settled together. Most of the money in a Women's Georgette Chiffon Tunic Top sits in three places: the cloth, the collar, and the labour that keeps the placket flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. For sheer cloth, plan the seam finish and the facing colour before sampling. A white facing behind a cream shell reads as a shadow. A blouse lives or dies at the collar and the cuff. Both need an interlining matched to the cloth weight, fused at a temperature the mill confirms. On light cloth, ease the sleeve head rather than gathering it. The sleeve should hold shape without puckers.

The collar reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The collar is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the placket, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Spec sheet, line by line

Shellchiffon, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Failure points worth designing out

  • Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
  • Collar fused too hard, giving a plastic edge that cannot be pressed into shape.
  • Placket cut on the bias by accident, so it twists after washing.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Options on the table

  • Placket: full, half, hidden, or none with a keyhole opening.
  • Collar: classic point, camp, band, or removable.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top