Women's Embroidered Chiffon Tunic Top
This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Under 200 gsm, plan to interface the collar. Without it, the seam ridge shows through at the first press. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. We start with chiffon on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. Shell buttons change the perceived price more than they change the cost. Decide early, because button size changes the placket width. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees. Set the placket before the collar. Two millimetres of shift at the button stand is visible.
Check the collar after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The collar reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the collar. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
The sheet we need before costing
| Shell | chiffon, swatch-approved, one dye lot for bulk |
| Body | blouse |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | no lining; faced yoke, cuffs and placket |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 100 pcs per colour |
Where this style fails in production
- Placket cut on the bias by accident, so it twists after washing.
- Sleeve gathered rather than eased, producing puckers that show on a plain cloth.
- Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Changes we can make at sample stage
- Back: plain, box pleat, or yoke with a loop.
- Collar: classic point, camp, band, or removable.
- Cuff: buttoned, elasticated, or turned back.
- Placket: full, half, hidden, or none with a keyhole opening.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.