Welcome to Bafinasa official website!

Casual Hot Summer Metallic Chiffon Tank Top

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. A Casual Hot Summer Metallic Chiffon Tank Top reads as a short brief until the pattern is cut, and the shape only holds when the collar, the placket and the hem allowance are settled together. Most of the money in a Casual Hot Summer Metallic Chiffon Tank Top sits in three places: the cloth, the collar, and the labour that keeps the placket flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with chiffon on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees. On light cloth, ease the sleeve head rather than gathering it. The sleeve should hold shape without puckers.

When the brief names the collar, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the collar as its own pattern piece so it can be changed without re-cutting the body.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the collar to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the collar.

Specification, item by item

Shellchiffon, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closureinvisible centre-back zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

Failure points worth designing out

  • Collar fused too hard, giving a plastic edge that cannot be pressed into shape.
  • Placket cut on the bias by accident, so it twists after washing.
  • Sleeve gathered rather than eased, producing puckers that show on a plain cloth.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Customisation that does not break the price

  • Cuff: buttoned, elasticated, or turned back.
  • Collar: classic point, camp, band, or removable.
  • Back: plain, box pleat, or yoke with a loop.
  • Placket: full, half, hidden, or none with a keyhole opening.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top