Welcome to Bafinasa official website!

Hot Summer Polyester Chiffon Palazzo Pants

Source:News / Time:2026-11-19

A Hot Summer Polyester Chiffon Palazzo Pants reads as a short brief until the pattern is cut, and the shape only holds when the shoulder seam, the side seam and the hem allowance are settled together. It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. Steam is used lightly. Too much heat flattens the volume the buyer is paying for. Chiffon moves on the cutting table. Lay it flat for thirty minutes before cutting, or every panel will be a different length. French seams are worth the extra minute. An overlocked edge shows as a dark line through a light chiffon.

If the hem is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. When the brief names the hem, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates.

Specification, item by item

Shellchiffon, swatch-approved, one dye lot for bulk
Bodychiffon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Lininghalf lined to the hip
Closurecovered button placket
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

What to check before bulk

  • Lining sewn to the same length as the shell, so the two drag each other.
  • Heavy needle thread showing through the shell under shop lights.
  • Cutting before the cloth relaxes, so the finished hem is uneven.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Sleeve: flutter, cap, or long with a cuff.
  • Layer count at the skirt: one, two, or three tiers.
  • Lining: full, to the knee, or a separate slip.
  • Print or solid, with placement controlled at the front panel.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top