Spring Summer Double Layer Chiffon Tunic Top
Most of the money in a Spring Summer Double Layer Chiffon Tunic Top sits in three places: the cloth, the collar, and the labour that keeps the placket flat after pressing. It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For chiffon, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Cuffs are cut in pairs from the same panel. A mismatched pair is the first thing an inspector sees. On light cloth, ease the sleeve head rather than gathering it. The sleeve should hold shape without puckers.
When the brief names the collar, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The collar is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Shoulder and neckline decide whether a Spring Summer Double Layer Chiffon Tunic Top looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the placket, not a redesign.
Specification, item by item
| Shell | chiffon, swatch-approved, one dye lot for bulk |
| Body | blouse |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | no lining; faced yoke, cuffs and placket |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
What to check before bulk
- Placket cut on the bias by accident, so it twists after washing.
- Collar fused too hard, giving a plastic edge that cannot be pressed into shape.
- Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Customisation that does not break the price
- Placket: full, half, hidden, or none with a keyhole opening.
- Back: plain, box pleat, or yoke with a loop.
- Collar: classic point, camp, band, or removable.
- Cuff: buttoned, elasticated, or turned back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.