Welcome to Bafinasa official website!

Spring Summer Chiffon Lurex Palazzo Pants

Source:News / Time:2026-11-19

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Most of the money in a Spring Summer Chiffon Lurex Palazzo Pants sits in three places: the cloth, the shoulder seam, and the labour that keeps the side seam flat after pressing.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. For chiffon, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. French seams are worth the extra minute. An overlocked edge shows as a dark line through a light chiffon. The lining is cut shorter and attached at the waist, so the shell floats over it. Steam is used lightly. Too much heat flattens the volume the buyer is paying for.

Check the hem after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the hem, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam.

Spec sheet, line by line

Shellchiffon, swatch-approved, one dye lot for bulk
Bodychiffon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

The places this usually goes wrong

  • Over-pressed seams that kill the drape and make the dress look flat.
  • Lining sewn to the same length as the shell, so the two drag each other.
  • Heavy needle thread showing through the shell under shop lights.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Changes we can make at sample stage

  • Print or solid, with placement controlled at the front panel.
  • Lining: full, to the knee, or a separate slip.
  • Layer count at the skirt: one, two, or three tiers.
  • Sleeve: flutter, cap, or long with a cuff.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top