Welcome to Bafinasa official website!
Your Location: Home - News - Crinkle Chiffon Camisole

Crinkle Chiffon Camisole

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is chiffon, the inside is structure, and the two have to agree on the same sample. A Crinkle Chiffon Camisole reads as a short brief until the pattern is cut, and the shape only holds when the collar, the placket and the hem allowance are settled together. Most of the money in a Crinkle Chiffon Camisole sits in three places: the cloth, the collar, and the labour that keeps the placket flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. For chiffon, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. On light cloth, ease the sleeve head rather than gathering it. The sleeve should hold shape without puckers. Set the placket before the collar. Two millimetres of shift at the button stand is visible. A blouse lives or dies at the collar and the cuff. Both need an interlining matched to the cloth weight, fused at a temperature the mill confirms.

The collar is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. We keep the collar as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the collar. On this style the difference between a good and a poor fit is usually two centimetres at the placket, not a redesign.

The sheet we need before costing

Shellchiffon, swatch-approved, one dye lot for bulk
Bodyblouse
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningno lining; faced yoke, cuffs and placket
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

The places this usually goes wrong

  • Placket cut on the bias by accident, so it twists after washing.
  • Collar fused too hard, giving a plastic edge that cannot be pressed into shape.
  • Buttons sized to the sample rather than to the placket, so bulk splits the button stand.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Placket: full, half, hidden, or none with a keyhole opening.
  • Cuff: buttoned, elasticated, or turned back.
  • Collar: classic point, camp, band, or removable.
  • Back: plain, box pleat, or yoke with a loop.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Private label: woven label, care label and hangtag to your artwork.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top