Welcome to Bafinasa official website!

Burgundy Side Slit Cocktail Midi Dress for Women

Source:News / Time:2026-11-19

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is burgundy side slit cocktail midi dress for women: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

For structured crepe, jacquard or satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Under 200 gsm, plan to interface the bodice seam. Without it, the seam ridge shows through at the first press. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust.

The bodice seam reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The bodice seam is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Cocktail Midi Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

The sheet we need before costing

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwayburgundy
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

What to check before bulk

  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Schedule an in-line check after the bodice seam goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Changes we can make at sample stage

  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Back: centre zip, lace-up, or a covered button placket.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top