Welcome to Bafinasa official website!

Best for Women Navy Blue Sequin Cocktail Midi Dress

Source:News / Time:2026-11-19

Written down, the request is best for women navy blue sequin cocktail midi dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Best for Women Navy Blue Sequin Cocktail Midi Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

The bodice seam reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the bodice seam, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaynavy
Liningfully lined, bagged hem
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

What to check before bulk

  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Changes we can make at sample stage

  • Sleeve: sleeveless, cap, or detachable straps.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top