Welcome to Bafinasa official website!

For Women Striped Shift Casual Dresses

Source:News / Time:2026-11-19

Written down, the request is for women striped shift casual dresses: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Most of the money in a For Women Striped Shift Casual Dresses sits in three places: the cloth, the shoulder seam, and the labour that keeps the side seam flat after pressing. A For Women Striped Shift Casual Dresses reads as a short brief until the pattern is cut, and the shape only holds when the shoulder seam, the side seam and the hem allowance are settled together.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the shoulder seam. Without it, the seam ridge shows through at the first press. We start with cotton jersey or washed poplin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. This style is often worn without a slip, so check the inside seam finishes against light. Jersey is cut in a single layer in the direction of the grain. Two layers can shift and twist the hem. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow.

The shift reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the shift after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Casual Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Failure points worth designing out

  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Shrinkage tested on a different dye lot, so the first wash shortens the dress.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Print placement or solid with a contrast binding.
  • Pockets: none, side seam, or patch.
  • Length: above the knee, at the knee, or midi.
  • Sleeve: short, cap, or long with a rib cuff.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top