Welcome to Bafinasa official website!

Emerald Green Halter Neck Cocktail Midi Dress for Women

Source:News / Time:2026-11-19

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. For structured crepe, jacquard or satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust.

If the halter is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. When the brief names the halter, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the bodice seam. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Liningbodice lined, skirt lined
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

Where this style fails in production

  • Topstitch showing through a satin shell after pressing.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

What we can change for you

  • Sleeve: sleeveless, cap, or detachable straps.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top