Welcome to Bafinasa official website!

Emerald Green Long Sleeve Cocktail Midi Dress for Women

Source:News / Time:2026-11-19

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is structured crepe, jacquard or satin in green, the inside is structure, and the two have to agree on the same sample. A Emerald Green Long Sleeve Cocktail Midi Dress for Women reads as a short brief until the pattern is cut, and the shape only holds when the bodice seam, the waist seam and the hem allowance are settled together.

Under 200 gsm, plan to interface the bodice seam. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. For structured crepe, jacquard or satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip.

The long sleeve is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the long sleeve, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Cocktail Midi Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Lininghalf lined to the hip
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

What to check before bulk

  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Topstitch showing through a satin shell after pressing.
  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. In bulk the failures cluster: skipped stitches on the bodice seam, shading between panels, and hems that go wavy after pressing.

Changes we can make at sample stage

  • Back: centre zip, lace-up, or a covered button placket.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Private label: woven label, care label and hangtag to your artwork.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top