Welcome to Bafinasa official website!

For Women Emerald Green Satin Cocktail Midi Dress

Source:News / Time:2026-11-19

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Most of the money in a For Women Emerald Green Satin Cocktail Midi Dress sits in three places: the cloth, the bodice seam, and the labour that keeps the waist seam flat after pressing.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. We start with satin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

Check the bodice seam after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the bodice seam to move at different rates.

Spec sheet, line by line

Shellsatin, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Liningbodice lined, skirt lined
Closurecovered button placket
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

The places this usually goes wrong

  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • Topstitch showing through a satin shell after pressing.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

In bulk the failures cluster: skipped stitches on the bodice seam, shading between panels, and hems that go wavy after pressing. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Options on the table

  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Back: centre zip, lace-up, or a covered button placket.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top