Welcome to Bafinasa official website!

For Women Navy Blue Wedding Guest Cocktail Midi Dress

Source:News / Time:2026-11-19

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. It helps to separate what the customer sees from what the factory feels. The outside is structured crepe, jacquard or satin in navy, the inside is structure, and the two have to agree on the same sample. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Under 200 gsm, plan to interface the bodice seam. Without it, the seam ridge shows through at the first press. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

When the brief names the bodice seam, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the bodice seam. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

What goes on the spec sheet

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaynavy
Liningbodice lined, skirt lined
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

What to check before bulk

  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • Topstitch showing through a satin shell after pressing.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

Customisation that does not break the price

  • Sleeve: sleeveless, cap, or detachable straps.
  • Back: centre zip, lace-up, or a covered button placket.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top