Welcome to Bafinasa official website!

Cowl Neckline Emerald Green Wrap Cocktail Midi Dress

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is structured crepe, jacquard or satin in green, the inside is structure, and the two have to agree on the same sample. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust.

When the brief names the wrap, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the wrap after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

What to check before bulk

  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the bodice seam, shading between panels, and hems that go wavy after pressing.

What we can change for you

  • Sleeve: sleeveless, cap, or detachable straps.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Back: centre zip, lace-up, or a covered button placket.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top