Best for Women Burgundy Sequin Cocktail Midi Dress
Written down, the request is best for women burgundy sequin cocktail midi dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.
Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. We start with structured crepe, jacquard or satin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth.
We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body. When the brief names the bodice seam, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Best for Women Burgundy Sequin Cocktail Midi Dress looks expensive. Both are set by the block, not by the sewing.
Specification, item by item
| Shell | a structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk |
| Body | cocktail midi dress |
| Length | midi |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Decoration applied before fitting, so the panel cannot be adjusted without removing it.
- Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
- A close fit approved on the form, then rejected on a body because the armhole was cut too high.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the bodice seam goes on. Catching a rotation there costs minutes; catching it at final costs the order. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
Changes we can make at sample stage
- Back: centre zip, lace-up, or a covered button placket.
- Sleeve: sleeveless, cap, or detachable straps.
- Neckline: square, V, or one shoulder with a faced edge.
- Decoration: none, tonal embroidery, or a beaded motif at the waist.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.