Welcome to Bafinasa official website!

For Women Emerald Green Sequin Cocktail Midi Dress

Source:News / Time:2026-11-19

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the bodice seam. A For Women Emerald Green Sequin Cocktail Midi Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

If the bodice seam is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the bodice seam. Shoulder and neckline decide whether a For Women Emerald Green Sequin Cocktail Midi Dress looks expensive. Both are set by the block, not by the sewing.

What goes on the spec sheet

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwaygreen
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

The places this usually goes wrong

  • Topstitch showing through a satin shell after pressing.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the bodice seam, shading between panels, and hems that go wavy after pressing. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Customisation that does not break the price

  • Neckline: square, V, or one shoulder with a faced edge.
  • Back: centre zip, lace-up, or a covered button placket.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top