Welcome to Bafinasa official website!

Burgundy Cowl Neckline Satin Cocktail Midi Dress

Source:News / Time:2026-11-19

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. For satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust.

The bodice seam reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shellsatin, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwayburgundy
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

The places this usually goes wrong

  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Changes we can make at sample stage

  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Back: centre zip, lace-up, or a covered button placket.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top