Welcome to Bafinasa official website!

Burgundy Party Cocktail Midi Dress for Women

Source:News / Time:2026-11-19

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Burgundy Party Cocktail Midi Dress for Women can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Most of the money in a Burgundy Party Cocktail Midi Dress for Women sits in three places: the cloth, the bodice seam, and the labour that keeps the waist seam flat after pressing.

For structured crepe, jacquard or satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

When the brief names the bodice seam, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the bodice seam to move at different rates.

Specification, item by item

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwayburgundy
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

Where this style fails in production

  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Options on the table

  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top