Burgundy Casual Dresses for Work for Women
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Burgundy Casual Dresses for Work for Women reads as a short brief until the pattern is cut, and the shape only holds when the shoulder seam, the side seam and the hem allowance are settled together. Written down, the request is burgundy casual dresses for work for women: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow. Necklines are finished with a self-fabric binding or a rib, depending on how much recovery the cloth has. This style is often worn without a slip, so check the inside seam finishes against light.
We keep the pocket opening as its own pattern piece so it can be changed without re-cutting the body. Check the pocket opening after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Specification, item by item
| Shell | a 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk |
| Body | casual dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
What to check before bulk
- Jersey cut in two layers, giving a hem that twists after washing.
- Pocket bags cut too short, so they pull the skirt out at the hip.
- Topstitch too tight on a knit, causing the seam to break.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Changes we can make at sample stage
- Print placement or solid with a contrast binding.
- Sleeve: short, cap, or long with a rib cuff.
- Length: above the knee, at the knee, or midi.
- Pockets: none, side seam, or patch.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.