Welcome to Bafinasa official website!

Best for Women Burgundy Women's Cocktail Midi Dress

Source:News / Time:2026-11-19

Written down, the request is best for women burgundy women's cocktail midi dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Most of the money in a Best for Women Burgundy Women's Cocktail Midi Dress sits in three places: the cloth, the bodice seam, and the labour that keeps the waist seam flat after pressing. It helps to separate what the customer sees from what the factory feels. The outside is structured crepe, jacquard or satin in burgundy, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

For structured crepe, jacquard or satin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with structured crepe, jacquard or satin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The zip is set at the back with a facing that stays flat, and the seam is tapered so it does not widen at the hip. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth. The bodice is fitted at the middle size with real underwear, then graded without adding ease at the bust.

Check the bodice seam after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The bodice seam reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the bodice seam. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

What goes on the spec sheet

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwayburgundy
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

What to check before bulk

  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • Decoration applied before fitting, so the panel cannot be adjusted without removing it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the bodice seam, shading between panels, and hems that go wavy after pressing.

Changes we can make at sample stage

  • Back: centre zip, lace-up, or a covered button placket.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Neckline: square, V, or one shoulder with a faced edge.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top