Welcome to Bafinasa official website!

For Women Burgundy Wedding Guest Cocktail Midi Dress

Source:News / Time:2026-11-19

A For Women Burgundy Wedding Guest Cocktail Midi Dress reads as a short brief until the pattern is cut, and the shape only holds when the bodice seam, the waist seam and the hem allowance are settled together. A For Women Burgundy Wedding Guest Cocktail Midi Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.

Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with structured crepe, jacquard or satin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. Decoration goes on after fitting. Beads and appliques change the weight of a panel and the way it hangs. A cocktail dress is cut close enough that seam allowances have to be pressed before they are joined. Otherwise the line shows through the cloth. A midi length is measured at the front and back separately. The back hem usually needs an extra centimetre.

We keep the bodice seam as its own pattern piece so it can be changed without re-cutting the body. The bodice seam is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella structured crepe, a jacquard, or a satin backed with soft interfacing, swatch-approved, one dye lot for bulk
Bodycocktail midi dress
Lengthmidi
Colourwayburgundy
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

Failure points worth designing out

  • Topstitch showing through a satin shell after pressing.
  • A close fit approved on the form, then rejected on a body because the armhole was cut too high.
  • Back hem one centimetre shorter than the front, visible as soon as the wearer walks.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Neckline: square, V, or one shoulder with a faced edge.
  • Decoration: none, tonal embroidery, or a beaded motif at the waist.
  • Back: centre zip, lace-up, or a covered button placket.
  • Sleeve: sleeveless, cap, or detachable straps.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top