Welcome to Bafinasa official website!

For Women Charcoal Grey Midi Casual Dresses

Source:News / Time:2026-11-19

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the shoulder seam. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. It helps to separate what the customer sees from what the factory feels. The outside is cotton jersey or washed poplin in grey, the inside is structure, and the two have to agree on the same sample. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.

We start with cotton jersey or washed poplin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow. A casual dress has to survive a washing machine. Confirm shrinkage on the actual lot before the pattern is final.

The pocket opening is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the pocket opening, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthmidi
Colourwaygrey
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

The places this usually goes wrong

  • Shrinkage tested on a different dye lot, so the first wash shortens the dress.
  • Topstitch too tight on a knit, causing the seam to break.
  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Schedule an in-line check after the shoulder seam goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Options on the table

  • Length: above the knee, at the knee, or midi.
  • Sleeve: short, cap, or long with a rib cuff.
  • Print placement or solid with a contrast binding.
  • Pockets: none, side seam, or patch.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top