Welcome to Bafinasa official website!

Best for Women Charcoal Grey Midi Casual Dresses

Source:News / Time:2026-11-19

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the shoulder seam. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is cotton jersey or washed poplin in grey, the inside is structure, and the two have to agree on the same sample.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Necklines are finished with a self-fabric binding or a rib, depending on how much recovery the cloth has. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow. Stitch with a stretch needle and a light press. A heavy hand leaves waves that show on a plain colour.

The pocket opening is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. The pocket opening reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. On this style the difference between a good and a poor fit is usually two centimetres at the side seam, not a redesign.

The sheet we need before costing

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthmidi
Colourwaygrey
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

What to check before bulk

  • Jersey cut in two layers, giving a hem that twists after washing.
  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Topstitch too tight on a knit, causing the seam to break.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the shoulder seam, shading between panels, and hems that go wavy after pressing.

Changes we can make at sample stage

  • Print placement or solid with a contrast binding.
  • Sleeve: short, cap, or long with a rib cuff.
  • Length: above the knee, at the knee, or midi.
  • Pockets: none, side seam, or patch.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top