Burgundy Tiered Casual Dresses for Women
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
We start with cotton jersey or washed poplin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. For cotton jersey or washed poplin, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Structure and seams
The build follows the same order on every size. These are the steps where the shape is won or lost. Jersey is cut in a single layer in the direction of the grain. Two layers can shift and twist the hem. Stitch with a stretch needle and a light press. A heavy hand leaves waves that show on a plain colour. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow.
When the brief names the tiered, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The tiered reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam.
Spec sheet, line by line
| Shell | a 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk |
| Body | casual dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | half lined to the hip |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
What to check before bulk
- Jersey cut in two layers, giving a hem that twists after washing.
- Shrinkage tested on a different dye lot, so the first wash shortens the dress.
- Topstitch too tight on a knit, causing the seam to break.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the shoulder seam, shading between panels, and hems that go wavy after pressing. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Options on the table
- Length: above the knee, at the knee, or midi.
- Print placement or solid with a contrast binding.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.