Welcome to Bafinasa official website!

Church Tiered Dress Accessories for

Source:News / Time:2026-11-19

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Church Tiered Dress Accessories for can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is crepe or cotton sateen, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

We start with crepe or cotton sateen on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Under 200 gsm, plan to interface the shoulder line. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Modesty panels are sewn as a separate facing and tacked at the side seams so they stay flat. Length is measured from the waist to the floor in the shoes the dress will be worn with. Lining is standard here. A 65 to 75 gsm taffeta lets the dress hang straight without adding bulk.

The tiered is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. We keep the tiered as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder line. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

The sheet we need before costing

Shella 180-240 gsm crepe or a lined cotton sateen, swatch-approved, one dye lot for bulk
Bodychurch dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

What to check before bulk

  • Hems cut on a curve without a proper let-out, so the bottom ripples.
  • Neckline cut too wide, so the dress needs a camisole the customer did not order.
  • Sleeve cap gathered, producing puckers that show in a photograph taken in daylight.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

What we can change for you

  • Sleeve: short, half, or three-quarter.
  • Overlay in lace or plain chiffon, lined to the same length as the shell.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top