Welcome to Bafinasa official website!
Your Location: Home - News - Under Silk Casual Dress

Under Silk Casual Dress

Source:News / Time:2026-11-19

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Under Silk Casual Dress reads as a short brief until the pattern is cut, and the shape only holds when the shoulder seam, the side seam and the hem allowance are settled together. Written down, the request is under silk casual dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Under 200 gsm, plan to interface the shoulder seam. Without it, the seam ridge shows through at the first press. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. For silk, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow. Necklines are finished with a self-fabric binding or a rib, depending on how much recovery the cloth has. This style is often worn without a slip, so check the inside seam finishes against light.

The pocket opening reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The pocket opening is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam.

What goes on the spec sheet

Shellsilk, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

What to check before bulk

  • Shrinkage tested on a different dye lot, so the first wash shortens the dress.
  • Jersey cut in two layers, giving a hem that twists after washing.
  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Changes we can make at sample stage

  • Sleeve: short, cap, or long with a rib cuff.
  • Pockets: none, side seam, or patch.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top