Welcome to Bafinasa official website!

Retro Terry Cloth Casual Dress

Source:News / Time:2026-11-19

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. A Retro Terry Cloth Casual Dress reads as a short brief until the pattern is cut, and the shape only holds when the shoulder seam, the side seam and the hem allowance are settled together.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Jersey is cut in a single layer in the direction of the grain. Two layers can shift and twist the hem. Pockets are a design decision here. They add use, but they also pull the skirt if the opening is too shallow. This style is often worn without a slip, so check the inside seam finishes against light.

The pocket opening reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the pocket opening as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the shoulder seam. On this style the difference between a good and a poor fit is usually two centimetres at the side seam, not a redesign.

Specification, item by item

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

Where this style fails in production

  • Topstitch too tight on a knit, causing the seam to break.
  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Jersey cut in two layers, giving a hem that twists after washing.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Changes we can make at sample stage

  • Sleeve: short, cap, or long with a rib cuff.
  • Print placement or solid with a contrast binding.
  • Pockets: none, side seam, or patch.
  • Length: above the knee, at the knee, or midi.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top