Welcome to Bafinasa official website!

Women's Summer Church Jacquard Church Two Piece Dress Suit

Source:News / Time:2026-11-19

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. For Church Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

Where this style fails in production

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Changes we can make at sample stage

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top