Welcome to Bafinasa official website!

Petite Lavender Two Piece Dress Suit Church Dress

Source:News / Time:2026-11-19

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

Where this style fails in production

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Customisation that does not break the price

  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top