Welcome to Bafinasa official website!

Fleece Above Knee Swing Casual Dress

Source:News / Time:2026-11-19

Written down, the request is fleece above knee swing casual dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. It helps to separate what the customer sees from what the factory feels. The outside is cotton jersey or washed poplin, the inside is structure, and the two have to agree on the same sample.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Necklines are finished with a self-fabric binding or a rib, depending on how much recovery the cloth has. Jersey is cut in a single layer in the direction of the grain. Two layers can shift and twist the hem.

We keep the pocket opening as its own pattern piece so it can be changed without re-cutting the body. The pocket opening is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the shoulder seam to move at different rates.

The sheet we need before costing

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurecovered button placket
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • Shrinkage tested on a different dye lot, so the first wash shortens the dress.
  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Schedule an in-line check after the shoulder seam goes on. Catching a rotation there costs minutes; catching it at final costs the order. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Print placement or solid with a contrast binding.
  • Length: above the knee, at the knee, or midi.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top