Welcome to Bafinasa official website!

Women's Terry Cloth Relaxed Fit Casual Knee Length Dress

Source:News / Time:2026-11-19

A Women's Terry Cloth Relaxed Fit Casual Knee Length Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Most of the money in a Women's Terry Cloth Relaxed Fit Casual Knee Length Dress sits in three places: the cloth, the shoulder seam, and the labour that keeps the side seam flat after pressing. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Under 200 gsm, plan to interface the shoulder seam. Without it, the seam ridge shows through at the first press. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. We start with cotton jersey or washed poplin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. This style is often worn without a slip, so check the inside seam finishes against light. A casual dress has to survive a washing machine. Confirm shrinkage on the actual lot before the pattern is final. Jersey is cut in a single layer in the direction of the grain. Two layers can shift and twist the hem.

When the brief names the relaxed fit, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the relaxed fit after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

The sheet we need before costing

Shella 160 to 220 gsm cotton jersey or a washed poplin, swatch-approved, one dye lot for bulk
Bodycasual dress
Lengthknee length
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

What to check before bulk

  • Pocket bags cut too short, so they pull the skirt out at the hip.
  • Topstitch too tight on a knit, causing the seam to break.
  • Shrinkage tested on a different dye lot, so the first wash shortens the dress.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Changes we can make at sample stage

  • Print placement or solid with a contrast binding.
  • Sleeve: short, cap, or long with a rib cuff.
  • Length: above the knee, at the knee, or midi.
  • Pockets: none, side seam, or patch.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top