Wholesale Emerald Green Tube Bodycon Dress for Club
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Most of the money in a Wholesale Emerald Green Tube Bodycon Dress for Club sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.
Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.
The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Shoulder and neckline decide whether a Wholesale Emerald Green Tube Bodycon Dress for Club looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
What to check before bulk
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Cloth with insufficient recovery, so the dress grows through the day.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
What we can change for you
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Bonded or sewn finish at the neckline and armhole.
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
