Wholesale Emerald Green Halter Neck Bodycon Dress for Club
It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in green, the inside is structure, and the two have to agree on the same sample. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel.
We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.
Check the halter after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The halter reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Wholesale Emerald Green Halter Neck Bodycon Dress for Club looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
What to check before bulk
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- Cloth with insufficient recovery, so the dress grows through the day.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Options on the table
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
