Wholesale Emerald Green Velvet Bodycon Dress
It helps to separate what the customer sees from what the factory feels. The outside is velvet in green, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Written down, the request is wholesale emerald green velvet bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.
When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Shoulder and neckline decide whether a Wholesale Emerald Green Velvet Bodycon Dress looks expensive. Both are set by the block, not by the sewing. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
The sheet we need before costing
| Shell | velvet, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | half lined to the hip |
| Closure | stretch panel, no zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing.
Changes we can make at sample stage
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
